Lubrication - The Secret of Bearing Lubrication to Ensure Optimal Bearing Life

At the heart of almost every industrial facility are electric motors, which can render equipment inoperative should their rolling element bearings fail - an occurrence more common than necessary due to strain resulting from improper lubrication.

Typical Causes of Bearing Failure

Typical causes of bearing failure include:

  • Loss of Lubricant - if the bearing is not re-greased at the appropriate interval, with the proper amount of grease, or if the oil is removed from the base of the grease by overheating, loss of lubricant can occur and contribute to equipment failure.
  • Grease Incompatibility - not all greases are compatible with each other. It is important to stay with the same grease or a compatible substitute for the life of a bearing.
  • Incorrect Grease - be sure to use the correct grease for your application. Some bearing designs and applications only need General Purpose (GP) grease while others require Extreme Pressure (EP) grease.
  • Grease Degradation - grease hardening, chemical breakdown caused by excessive heat, and oil separation from grease base are common types of grease degradation.
  • Excess Lubrication - occurs mainly with open face bearings, when excess grease gets between the inner bearing capos and the shaft. Grease covering the end windings of the insulation system can cause both winding and bearing failure.

Minimizing Bearing Failures

Proper re-greasing procedures also play a large role in preventing bearing failure. Following strict re-greasing steps in the correct sequence helps to minimize failures:

  • Re-grease a bearing while the motor is running and hot, or after the motor is removed from service and the grease is still hot. Under operational conditions, the grease is less viscous;
  • Ensure the grease gun contains the right lubricant for the bearings to be re-greased;
  • Clean the areas around the fill and drain fittings to ensure contaminants are not introduced into the bearing cavity;
  • Remove the drain fitting;
  • Leave the draining plug out for the duration of the re-greasing process;
  • With the motor running at operating temperature, add the recommended quantity of grease, or add slowly until it begins to move into the relief tube;
  • After excessive grease has been purged, the drain plug should be re-installed and the excessive grease cleaned from the drain area.

Factors to Monitor to Ensire Optimal Bearing Life

Motor noise and vibration should be monitored upon installation to establish a baseline. At regular intervals, these measurements should be checked and any sudden or significant change considered reason to check bearing lubrication. Motor bearing temperature is also a valuable analysis tool and should be monitored and trended over time. An increasing trend could be an indicator of the need to renew the grease or that the bearings are over-greased. Finally, attention should be paid to any high frequency noise output or vibration level as they may be a sign of bearing lubrication trouble.

This information has been sourced, reviewed and adapted from materials provided by Dow Corning.

For more information on this source, please visit Dow Corning.

Citations

Please use one of the following formats to cite this article in your essay, paper or report:

  • APA

    Dow Corning. (2019, May 28). Lubrication - The Secret of Bearing Lubrication to Ensure Optimal Bearing Life. AZoM. Retrieved on March 01, 2024 from https://www.azom.com/article.aspx?ArticleID=4792.

  • MLA

    Dow Corning. "Lubrication - The Secret of Bearing Lubrication to Ensure Optimal Bearing Life". AZoM. 01 March 2024. <https://www.azom.com/article.aspx?ArticleID=4792>.

  • Chicago

    Dow Corning. "Lubrication - The Secret of Bearing Lubrication to Ensure Optimal Bearing Life". AZoM. https://www.azom.com/article.aspx?ArticleID=4792. (accessed March 01, 2024).

  • Harvard

    Dow Corning. 2019. Lubrication - The Secret of Bearing Lubrication to Ensure Optimal Bearing Life. AZoM, viewed 01 March 2024, https://www.azom.com/article.aspx?ArticleID=4792.

Tell Us What You Think

Do you have a review, update or anything you would like to add to this article?

Leave your feedback
Your comment type
Submit
Azthena logo

AZoM.com powered by Azthena AI

Your AI Assistant finding answers from trusted AZoM content

Your AI Powered Scientific Assistant

Hi, I'm Azthena, you can trust me to find commercial scientific answers from AZoNetwork.com.

A few things you need to know before we start. Please read and accept to continue.

  • Use of “Azthena” is subject to the terms and conditions of use as set out by OpenAI.
  • Content provided on any AZoNetwork sites are subject to the site Terms & Conditions and Privacy Policy.
  • Large Language Models can make mistakes. Consider checking important information.

Great. Ask your question.

While we only use edited and approved content for Azthena answers, it may on occasions provide incorrect responses. Please confirm any data provided with the related suppliers or authors. We do not provide medical advice, if you search for medical information you must always consult a medical professional before acting on any information provided.

Your questions, but not your email details will be shared with OpenAI and retained for 30 days in accordance with their privacy principles.

Please do not ask questions that use sensitive or confidential information.

Read the full Terms & Conditions.