Researchers Propose New Approach for Accounting Plastic Anisotropy in Metal Forming Processes

RUDN University engineers have shown that theoretical calculations traditionally used to describe the compression of metal workpieces, do not take into account an important property of materials. Scientists have proposed a new approach that considered the missing property and showed that the final result, in this case, changes by 15-20%. The study is published in Materials.

The metal details are obtained by forming processes, which include for example rolling, extrusion, forging, as well as upsetting a cylindrical workpiece (when it is increased in diameter with a reduction in length). The practical application of upsetting goes together with theoretical models, but they are based on an initially incorrect assumption.

It is usually assumed that the properties of the material are isotropic, that is, the same in all directions. In reality, this is not the case and the properties are anisotropic. RUDN University engineers proposed a new approach to theoretical calculations and showed that considering anisotropy significantly affects the cylinder draft.

"The analysis of cylinder's upsetting is usually based on isotropic models. In addition, these solutions ignore the regime of sticking on the friction surface, which always occurs in exact solutions near the axis of symmetry. In turn, the sticking regime leads to the appearance of a rigid region moving together with the plate. Neglecting the anisotropy of the material and the noted properties of exact solutions makes the practical value of these solutions questionable.

Our overall motivation was to demonstrate, using a simple example, that plastic anisotropy, which is a very common property of metallic materials, should not be ignored in upper bound solutions for metal forming processes", said Sergei Alexandrov, professor at RUDN University's Department of Civil Engineering.

The researchers studied a problem in which an entire metal cylinder is pressed by two parallel plates. The speed of the plates is set, the dimensions of the cylinder are known. It is assumed that the physical properties of the cylinder are orthotropic, that is, they differ in three perpendicular directions. RUDN University engineers took the upper bound theorem as the basis of theoretical analysis. Hill's quadratic yield criterion was also used for calculations, which connects stresses along different axes in a certain combination.

RUDN University engineers tested the theoretical calculations on numerical examples -; four materials with different anisotropies. The results showed that anisotropy affects the force that must be applied to upset a cylinder. The difference in strength was 15-20%. This is explained by the fact that due to anisotropy there are regions inside the cylinder that interact with each other in different ways, there is friction and sticking.

"A distinguishing feature of the solution is that plastic anisotropy and the existence of a rigid region are taken into account. The existence of the rigid region automatically means that there is a region of sticking friction. It can be concluded that Plastic anisotropy affects the limit load required to deform the specimen. It may increase or decrease the limit load as compared to the isotropic case", said Sergei Alexandrov, professor at RUDN University's Department of Civil Engineering.


Tell Us What You Think

Do you have a review, update or anything you would like to add to this news story?

Leave your feedback
Your comment type
Azthena logo powered by Azthena AI

Your AI Assistant finding answers from trusted AZoM content

Azthena logo with the word Azthena

Your AI Powered Scientific Assistant

Hi, I'm Azthena, you can trust me to find commercial scientific answers from

A few things you need to know before we start. Please read and accept to continue.

  • Use of “Azthena” is subject to the terms and conditions of use as set out by OpenAI.
  • Content provided on any AZoNetwork sites are subject to the site Terms & Conditions and Privacy Policy.
  • Large Language Models can make mistakes. Consider checking important information.

Great. Ask your question.

While we only use edited and approved content for Azthena answers, it may on occasions provide incorrect responses. Please confirm any data provided with the related suppliers or authors. We do not provide medical advice, if you search for medical information you must always consult a medical professional before acting on any information provided.

Your questions, but not your email details will be shared with OpenAI and retained for 30 days in accordance with their privacy principles.

Please do not ask questions that use sensitive or confidential information.

Read the full Terms & Conditions.