Underfill Takes on a Bigger Role as Semiconductor Packaging Shrinks

Research published in Materials Today Electronics shows that higher interconnect density is pushing solder-joint dimensions into the sub-100 μm range in advanced chiplet-based packages, increasing reliability challenges faced by manufacturers. With AI, automotive, medical and consumer applications driving demand for compact assemblies, techniques traditionally associated with semiconductor manufacturing are now relevant to electronics manufacturing. Tony Sui, VP of manufacturing at Ryder Industries, a premium provider of electronics manufacturing services, explains why one of those techniques is underfill.

Image Credit: Ryder Industries

Underfill is typically an epoxy-based material applied beneath components such as ball grid arrays (BGAs). A BGA has an array of tiny solder balls underneath the component, which provide the electrical connections to the printed circuit board (PCB).

As these connections become smaller and more closely spaced, they become vulnerable to mechanical and thermal stress. Underfill fills the space beneath the component and around the solder joints, redistributing thermo-mechanical stress, mitigating thermal cycling and vibration fatigue, and thereby extending service life in harsh environments.

A main problem underfill addresses is the difference in coefficient of thermal expansion (CTE) between materials within an electronic assembly. Silicon, solder and PCB materials expand and contract at different rates as temperatures change, putting stress on solder joints during repeated heating and cooling.

A 2025 review published in Polymers identifies thermomechanical stress as one of the “most pervasive reliability challenges in electronic packaging”, with CTE mismatch between materials a key cause. By filling the gap, underfill helps redistribute this stress away from individual solder joints and across the wider component structure. It also provides resistance to mechanical stresses such as vibration, shock and drop, significantly enhancing the board-level reliability of the package.

From Semiconductor Manufacturing to EMS

Underfill has been commonly used in semiconductor and IC manufacturing in the past, but today’s electronic assemblies are incorporating smaller and more sophisticated packages, meaning that its uses are expanding.

BGAs, chip-scale packages (CSPs) and system-in-package (SiP) assemblies allow more functionality to be integrated into smaller spaces, but they also introduce demands on assembly processes and reliability.

This is most visible in compact modules across a range of sectors. In automotive applications, underfill can be used in ADAS ECUs, infotainment, telematics and LiDAR/radar modules. In medical applications, it can support implantable devices, wearable monitors and diagnostic equipment.

Meanwhile, industrial uses include IoT gateways, automation controllers and robotics modules, while AI and high-performance computing applications include advanced computing modules and high-density interconnects.

As a result, underfill is not a capability routinely required across conventional electronics assembly, and which is why most EMS providers support BGA pitches only down to 0.35 mm.

Reliability and Nitrogen Reflow

Ryder Industries has developed its underfill process to handle pitches down to 0.2 mm, where the connections are positioned extremely close together. The smaller the pitch, however, the less room there is for manufacturing variation.

At these dimensions, solder connections are smaller and more closely spaced, while the thermal and mechanical stresses affecting them remain unchanged. Underfill is therefore part of a wider reliability process involving material selection, surface preparation, dispensing, curing and inspection. As part of this reliability focus, a specialty underfill adhesive is employed that, in certain cases, can withstand up to three reflow passes without compromising performance.

The underfill material needs to flow consistently through spaces that can be only tens of microns high, before being cured. Ryder's inspection methods – automated x-ray inspection (AXI), ultrasonic scanning and cross-section analysis – check the finished result.

Thermal cycling can then assess how an assembly performs under repeated temperature changes. JEDEC's JESD22-A104 standard includes test conditions ranging from -40 °C to +85 °C, with Ryder's process tested through 800 cycles within this temperature range.

Nitrogen reflow is another complementary SMT capability that can support reliable fine-pitch assembly, which Ryder installed in 2026. During reflow soldering, nitrogen reduces the amount of oxygen around the PCB, helping to limit oxidation of solder and component surfaces.

Texas Instruments' assembly guidance reports shorter wetting times and fewer, smaller voids when using nitrogen compared with air in fine-pitch package assembly.

Together, these processes reflect the wider shift taking place across electronics manufacturing. As AI and other high-performance applications demand more functionality from smaller, more highly integrated modules, EMS providers are increasingly having to look beyond traditional assembly techniques.

Underfill is one example of a process once largely associated with semiconductor production that EMS providers are now being asked to deliver, particularly as fine-pitch connections and reliability become more important across electronic assemblies.

Unlike conventional EMS providers, Ryder performs underfill in-house, integrated directly into the same SMT production flow used for BGA mounting, nitrogen reflow, RF shielding, automated testing and automated packaging.

The process can accommodate bump pitches down to 0.2 mm, with ball-to-ball spacing approaching semiconductor-grade standards. Testing has also shown near-zero voiding, compared with a typical 4 percent acceptance target.

Such combination of underfill application, materials, inspection and testing within the same production flow reflects the requirements placed on EMS providers as electronic assemblies become smaller and more densely packed.

Tell Us What You Think

Do you have a review, update or anything you would like to add to this news story?

Leave your feedback
Your comment type
Submit

While we only use edited and approved content for Azthena answers, it may on occasions provide incorrect responses. Please confirm any data provided with the related suppliers or authors. We do not provide medical advice, if you search for medical information you must always consult a medical professional before acting on any information provided.

Your questions, but not your email details will be shared with OpenAI and retained for 30 days in accordance with their privacy principles.

Please do not ask questions that use sensitive or confidential information.

Read the full Terms & Conditions.